Concrete and Mortars
Comprehensive equipment for testing fresh and hardened concrete, mortars and cement-based materials. Suitable for concrete producers, construction sites and accredited laboratories. Our range also includes all equipment required for testing cement and mortars in accordance with Norwegian Standards, including NS-EN 459-2 and NS-EN 1015.
Typical Applications
- Quality control in concrete and mortar production
- On-site verification of mix consistency and workability
- Laboratory testing according to EN, ISO and ASTM standards
- Material development and certification testing
- Long-term durability and strength evaluation
Fresh and Hardened Concrete
Below is the complete selection of equipment for testing fresh and hardened concrete. The range covers density measurement, slump testing, air content, moulds, curing equipment, vibration and strength testing.
Density Meter
The density meter for concrete and aggregates is used to determine the density of hardened concrete and various aggregate materials.
Download brochure
Laboratory Mixers and Forced Mixers
We carry several types of laboratory mixers, ranging from simpler to more advanced models. Read more.
Surface Grinding Machine
Machine for grinding and leveling the surface of concrete specimens before strength testing.
Download brochure
Slump Test (Workability Test)
Slump test is used to check fresh concrete before casting.
Download brochure
L-Box SCC/SKB/AUV
For testing the spread and flow properties of SCC, SKB and AUV concrete.
The L-box is a testing tool used to assess the flow and passing ability of fresh concrete.
Download brochure
Air Content Meter
An air content meter is used to determine the air content in fresh concrete.
Download brochure
Moulds
Moulds for concrete cubes, cylinders, and prisms used to produce standardized specimens for testing and quality control in accordance with Norwegian Standards.
We supply a wide range of moulds for concrete testing.
Download brochure
Compression Testing Machines
Concrete compression testing machines for testing cubes in accordance with NS-EN 12390 Testing of hardened concrete.
Download brochure
Curing Tank
Used for curing concrete test specimens under controlled conditions and at a constant water temperature.
Download brochure
Vibration Table
Vibration table is used to process fresh concrete samples before curing.
Download brochure
Additional Products
We sell most types of equipment for concrete testing.
- Concrete scoops, flat and round
- Rubber mallets and hammers
- Plastic spray bottles
- Thermometers
Bending / Tensile Tester
The flexural tensile testing machine is used to measure the strength and elasticity of beams and slabs under bending and tension.
Download brochure
E-Modulus / FTS Press
The modulus of elasticity, or E-modulus, for concrete is an important parameter that describes the material’s stiffness and its ability to deform elastically under load.
Download brochure
Temperature Logger
Temperature logger used for recording temperature development in concrete during curing.
Temperature Logger, 4-Channel
Temperature Logger, 2-Channel
Water Permeability Tester
Equipment for testing water penetration and permeability in hardened concrete.
Norwegian Standard:
NS-EN 12390-8 Testing of hardened concrete – Part 8: Depth of penetration of water under pressure.
Download brochure
Schmidt Rebound Hammers
Testing of the compressive strength of concrete in completed concrete structures.
Also used to monitor strength development, for example in connection with the setting time of concrete. Read more.
Concrete Structures
Below is the full selection of instruments for inspecting, evaluating and testing concrete structures. These tools support structural assessment, reinforcement detection, adhesion testing, ultrasonic testing, chloride content measurement and surface evaluation.
Rebar Detectors / Profometers
Rebar detectors are used to locate reinforcing steel.
They can also detect the concrete cover and the diameter of the reinforcement bar.
Rebar detectors are part of the NDT equipment category (non-destructive testing).
GPR (Ground Penetrating Radar)
Ground-penetrating radar (GPR) is used for inspection of concrete structures and falls under the category of NDT equipment.
Bond Test Apparatus
Measurement of bond strength by pull-off testing
The bond test apparatus is available in 4 different models.
Pundit – Ultrasonic Tester
Part of the equipment used for NDT – Non-Destructive Testing.
- Inspection of concrete structures
- Detection of defects, objects, and thickness
- Real-time visualization
- Ultrasonic imaging system – 3D visualization
- The market’s lightest scanner – wireless
Download brochure
RCT – Chloride Meter
For determination of chloride content in hardened concrete.
- Fast and accurate
- On-site or in the laboratory
Complete set with calibrated RCT electrode.
Download brochure
Schmidt Hammer
Rebound hammer for non-destructive strength estimation and surface hardness evaluation of concrete. Read more.
Cement & Mortars
We supply all equipment required for testing cement and mortars in accordance with Norwegian Standards.
Consistency Meter
Consistency measurement of fresh mortar is an important process to ensure that the mortar has the correct workability and quality.
Air Content Meter for Cement Mortars
The 1-liter air content meter is used to determine the air content in fresh cement mortar.
Download brochure
Mortar Mixer
A mortar mixer is used for mixing various types of cement mortars for laboratory testing.
Download brochure
Compression and Flexural Testing Press
Our presses for testing hardened cement/mortar can be supplied in several versions.
Mortar Moulds
Moulds for preparing mortar specimens—typically cubes and prisms—for strength testing.
Penetrometer / Vicat
Both of these instruments are essential for ensuring that mortar and concrete meet the required standards and quality requirements in construction projects.
Contact
For more information about concrete and mortar testing equipment, please contact our Test Equipment team at Kamet-Röbäcks AS.
We support success from the ground up
